Roborock Qrevo series maintenance and guide

The Roborock Qrevo platform spans six generations of maintenance sets and a suction range from 5,500 Pa on the original Qrevo and P10 through to the flagship second-generation tier covering the Qrevo Curv 2 Pro, Qrevo EdgeT, and QX Revo Ultra. All share the dual spinning mop architecture and a multifunctional dock, but the brush type, dock wash temperature, side brush design, and maintenance set generation shift across tiers in ways that change every component’s service interval. This guide covers the full replacement schedule, explains how each named Qrevo model differs, and identifies the maintenance causes behind the most common platform faults.

Why Roborock Qrevo series robots need more frequent maintenance

Dual spinning mops concentrate pad wear at the outer edge

Unlike flat-dragging mops, the Qrevo platform drives two round microfibre pads in counter-rotation at up to 200 RPM with downward pressure applied. At that angular velocity the outer rim of each pad travels significantly faster than the centre, so wear concentrates at the edge while the inner fibres remain relatively fresh. A pad that looks serviceable from above can already be worn at the rim and will deposit streaks along tile grout or skirting boards before the centre shows any degradation at all. On FlexiArm-equipped models such as the Qrevo MaxV, Qrevo Pro, Qrevo Master, Qrevo Slim, Qrevo C Pro, Qrevo Curv, Qrevo Edge, Qrevo Curv 2 Pro, Qrevo EdgeT, and QX Revo Ultra, the pad extends outward on each revolution for wall-edge coverage, which amplifies the rim wear and shortens the inspection window further.

Suction tiers from 5,500 Pa to 18,500 Pa change filter loading dramatically

The Qrevo range spans nearly four times the suction variation of a typical robot family. At 5,500 Pa the original Qrevo and P10 load the HEPA filter at a moderate rate; under daily use, two to three months between changes is realistic. The 7,000 Pa tier covering the Qrevo S, Qrevo Plus, Qrevo Pro, Qrevo MaxV, and P10 Pro sits at a similar cadence. Stepping up to 10,000 Pa on the Qrevo L, Qrevo L Pro, Qrevo Master, and P10S Pro pulls that window closer to two months. At 18,500 Pa on the first-generation flagship tier covering the Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, and P20 Pro, and on the second-generation flagship tier covering the Qrevo Curv 2 Pro, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, the filter loads roughly three times faster than on the original Qrevo and needs replacement every two months under daily residential use.

DuoDivide anti-tangle brushes have a divider channel that requires its own service

The Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, Qrevo Master, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, and QX Revo Ultra use the DuoDivide brush: two parallel short-bristle rollers separated by a central spiral intake that guides hair toward the centre and sucks it up before it can wrap. The mechanism works well, but the central divider channel collects compressed fibre that is invisible unless both rollers are removed. Users who clean only the visible rollers report hair wrap returning after a few weeks; in almost every case the channel is loaded rather than the rollers worn. Both rollers must be removed and the channel cleared at every brush service for the anti-tangle design to function as intended. The Qrevo Slim instead uses dual all-rubber counter-rotating rollers, which resist hair wrap through a smooth-surface mechanism and require a wipe-down rather than a channel clear, but the roller grooves still collect compacted dust that should be inspected monthly.

Dock wash temperature and drying generation change the nozzle maintenance cadence

Three dock generations exist across the Qrevo range. The original Qrevo and Qrevo L use the first-generation Multifunctional Dock with cold-water mop wash and 45°C warm-air drying. The Qrevo MaxV, Qrevo Plus, and Qrevo Pro move to the Dock 2.0 with hot-water mop washing. The Qrevo Master, Qrevo Slim, Qrevo Curv, Qrevo Edge, Qrevo C, Qrevo C Pro, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Pro all ship with docks that wash mop pads at 75°C and use warm-air drying at a higher throughput. The elevated temperature dissolves grease more effectively but also precipitates limescale onto the spray nozzle faster; in hard-water areas the nozzle wipe interval drops from monthly to every two to three weeks on these models.

Models in this series compared

Model	Suction	Mop system	Brush type	Dock generation
Qrevo	5,500 Pa	Dual spinning, liftable	Single DuoRoller	Dock 1.0, cold wash, 45°C dry
P10	5,500 Pa	Dual spinning, liftable	Single DuoRoller	Dock 1.0, cold wash, 45°C dry
Qrevo S	7,000 Pa	Dual spinning, liftable	Single DuoRoller	Dock 1.0, cold wash, 45°C dry
Qrevo Plus	7,000 Pa	Dual spinning, liftable	Single DuoRoller	Dock 2.0, hot wash, 45°C dry
Qrevo Pro	7,000 Pa	Dual spinning with FlexiArm	Single DuoRoller	Dock 2.0, hot wash, 45°C dry
Qrevo MaxV	7,000 Pa	Dual spinning with FlexiArm	Single DuoRoller	Dock 2.0, hot wash, 45°C dry
P10 Pro	7,000 Pa	Dual spinning, liftable	Single DuoRoller	Dock 2.0, hot wash, 45°C dry
Qrevo L	10,000 Pa	Dual spinning, 10 mm lift	Single DuoRoller	Dock 1.0, 3-stage wash, warm-air dry
Qrevo L Pro	10,000 Pa	Dual spinning, 10 mm lift	Single DuoRoller	Dock 1.0, 3-stage wash, warm-air dry
Qrevo Master	10,000 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo Slim	11,000 Pa	Dual spinning with FlexiArm	Dual rubber counter-rotating	Dock 3.0, 75°C wash, warm-air dry
P10S Pro	10,000 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo C	18,500 Pa	Dual spinning, liftable	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo C Pro	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo Curv	18,500 Pa	Dual spinning with FlexiArm, 17 mm lift	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo Edge	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
P20 Pro	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo Curv 2 Pro	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo Curv 2 ProX	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo CurvX	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
Qrevo EdgeT	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
QX Revo Ultra	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry
P20 Ultra Plus	18,500 Pa	Dual spinning with FlexiArm	DuoDivide dual-roller	Dock 3.0, 75°C wash, warm-air dry

5,500 Pa entry tier: Qrevo and P10

The original Qrevo is the entry point for the Qrevo architecture, with 5,500 Pa suction, a single DuoRoller main brush, and the first-generation Multifunctional Dock using cold-water mop wash and 45°C warm-air drying. The P10 is the P-series market variant of the same platform and uses an identical maintenance set. Both are also retailed as QR52-00 and QX0PEA in certain markets.

7,000 Pa first-generation models

The Qrevo S, Qrevo Plus, Qrevo Pro, Qrevo MaxV, and P10 Pro all operate at 7,000 Pa and share the same maintenance set. The Qrevo Pro and Qrevo MaxV add the FlexiArm extending mop and forward AI camera, which shortens the mop pad inspection window. Models sold under SKU identifiers in this set include QRS02-00, QRS52-00, QRS51-01, QR1PES, QR0PEP, QX1PEC, and R100053.

10,000 to 11,000 Pa mid-tier models

The Qrevo L and Qrevo L Pro sit at 10,000 Pa with a 10 mm mop lift and a single DuoRoller brush, using a Dock 1.0 variant with three-stage washing. Also in this tier are QV 35A, QV 35S, QR 598, QR 798, QVRS02-00, QVRRS02-00, QVRRS52-00, and RR-QRL52-03-BLK. The Qrevo Master, Qrevo Slim, and P10S Pro form a separate sub-set at this suction tier, using the Dock 3.0 with 75°C washing and adding either the DuoDivide dual-roller or rubber-roller brush architecture. Also in this Master/Slim set: QRM52-00, V20, QC0CRL, and QR2PPS.

18,500 Pa first-generation flagship models

The Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, and P20 Pro all run at 18,500 Pa with the DuoDivide dual-roller and Dock 3.0, using the first-generation 18,500 Pa maintenance set. This tier also includes numerous regional and market-variant SKUs: Qrevo Curv 5A1, Qrevo Curv 5XC, Qrevo CurvC, Qrevo Curv S5X, Qrevo Edge 5V1, Qrevo EdgeC, Qrevo Edge S5A, V10VIV, Qrevo S5V, Qrevo 5AE, QRC01-01, QRC02-00, QRES02-00, QRES52-00, QRRC52-02, QRSP52-00, RRE0VCM, RRE0PEE, RRW0PEP. The Qrevo Curv is distinct within this group for the AdaptiLift chassis that raises the body for threshold crossing and lifts the mop pads 17 mm for carpet and dock return.

18,500 Pa second-generation flagship models

The Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus form the second-generation 18,500 Pa flagship tier. They share the DuoDivide dual-roller brush, FlexiArm extending mop, FlexiArm side brush, and Dock 3.0 with 75°C mop washing. Critically, this generation uses a revised maintenance set that is not interchangeable with the first-generation 18,500 Pa set used by the Qrevo Curv, Qrevo Edge, and their variants. Owners upgrading from a first-generation model must confirm which set their specific model requires; the maintenance schedule and service cadences remain identical between generations, but the replacement parts themselves differ. Regional SKU variants in this tier include RRE0VIS, RRE0VSC, and RRE0VSP.

Replacement parts and service intervals

Main brush roll

Clean every one to two weeks and replace every five to seven months under daily residential use. On DuoRoller single-brush models, cleaning means cutting wrapped hair along the full roll length with scissors, clearing both end-cap bearing holes with a toothpick, and inspecting the brush chamber for debris packed against the housing. This covers the Qrevo, P10, Qrevo S, Qrevo Plus, Qrevo Pro, Qrevo MaxV, P10 Pro, Qrevo L, and Qrevo L Pro. On DuoDivide models, including the Qrevo Master, P10S Pro, Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, P20 Pro, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus: remove both rollers, clean each individually, and clear the central divider channel at every service. The channel is the mechanism that makes the anti-tangle design work; a loaded channel returns hair wrap to both rollers simultaneously, which can look like brush failure but is a maintenance gap. The Qrevo Slim uses dual all-rubber rollers; the smooth surface lets hair slide rather than wrap, so service is a wipe-down of each roller and a monthly inspection of the groove channels for compacted dust.

HEPA filter

Tap all four edges of the filter frame over a waste bin every one to two weeks. Do not wash the filter with water unless the product documentation explicitly confirms it is washable; washing degrades the filter medium even when the frame appears intact. Replace when the filter shifts from white to a consistent mid-grey. On the 5,500 Pa and 7,000 Pa tier models, including the Qrevo, P10, Qrevo S, Qrevo Plus, Qrevo Pro, Qrevo MaxV, and P10 Pro, replace every two to three months. On the 10,000 Pa tier covering Qrevo L, Qrevo L Pro, Qrevo Master, P10S Pro, and the 11,000 Pa Qrevo Slim, replace every two months under daily use. On the 18,500 Pa models across both generations, including the Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, P20 Pro, Qrevo Curv 2 Pro, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, replace every two months. The measurable airflow increase at this suction tier loads the filter medium noticeably faster than on lower-Pa models.

Mop pads

Docks that auto-wash after every run handle surface hygiene, but the dock cannot reverse the mechanical wear from 200 RPM spinning. Inspect at eight weeks on non-FlexiArm models and replace when the outer edge has lost its nap, the pad feels stiff after a dock wash, or persistent discolouration remains despite repeated washing cycles. On FlexiArm-equipped models such as the Qrevo MaxV, Qrevo Pro, Qrevo Master, Qrevo Slim, Qrevo C Pro, Qrevo Curv, Qrevo Edge, P20 Pro, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, the outer edge of the pad travels further on each revolution during extension, concentrating wear at the rim; inspect at six weeks on these models. On cold-wash dock models, pad soiling also becomes more persistent over time because 45°C drying alone does not dissolve greasy residues; planned early replacement is generally more cost-effective than extended manual cleaning attempts.

Side brush

Inspect the side brush post weekly. Hair and thread wrap around the base and apply steady strain to the brush motor. Clear accumulation with a toothpick or small scissors and replace the brush every three to six months, shortening that window in homes with pets or long hair. On FlexiArm side brush models such as the Qrevo Curv, Qrevo Edge, Qrevo C Pro, Qrevo Master, Qrevo Slim, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, the arc arm that carries the brush outward for wall coverage has a rail that collects grit and hair over time. A rail with even a small amount of resistance prevents the brush from completing its full extension arc, so the robot sweeps cleanly through the room centre but leaves a visible dust strip along skirting boards. Wipe the arm rail monthly with a dry cloth and confirm by hand that the arm swings freely through its complete travel before the next cleaning session.

Dock dustbag

Qrevo multifunctional docks use sealed dust bags ranging from 2.5 to 3.5 litres depending on the dock generation. Under daily use with auto-empty running after every session, a three to five week replacement cadence is realistic in a standard household. A full bag causes the auto-empty cycle to stall mid-transfer, leaving the robot’s onboard dustbin unable to accept new material on the following run. Roborock’s published figure of up to seven weeks applies to lighter-than-average environments, not to pet households or homes with carpet. Replace earlier rather than later if in doubt.

Dock dirty-water tank and spray nozzles

Empty and rinse the dirty-water tank every two to three days. Qrevo docks run a mop wash after every session on hot-wash and 75°C models, filling the tank noticeably faster than on robots that require manual mop cleaning. On cold-wash and 45°C models such as the Qrevo, P10, Qrevo S, Qrevo L, and Qrevo L Pro, wipe the dock spray nozzles monthly to prevent limescale build-up. On the 75°C Dock 3.0 models, including the Qrevo Master, Qrevo Slim, Qrevo Curv, Qrevo Edge, Qrevo C, Qrevo C Pro, P20 Pro, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, the higher wash temperature precipitates mineral deposits onto the nozzle faster; in hard-water areas every two to three weeks is the safer cadence. If mop pads return with one side visibly less clean than the other, a partially blocked nozzle is the first thing to investigate.

Sensor windows and obstacle cameras

Wipe the forward camera window, LDS lidar port, and underside cliff sensors weekly with a dry microfibre cloth. On the low-profile Qrevo Slim at 8.2 cm body height, and on AdaptiLift-equipped models such as the Qrevo Curv, Qrevo Curv 2 Pro, and Qrevo CurvX, sensor windows sit closer to the floor dust layer than on taller models and benefit from more frequent attention. The Qrevo MaxV uses a forward AI obstacle camera; a smudged lens is a common cause of unnecessary detours around clear floor.

Battery

Roborock Qrevo robots use lithium-ion battery packs rated between 5,200 mAh and 6,400 mAh depending on the model tier. Under typical daily use, a Qrevo battery delivers its rated runtime reliably for approximately two to three years before capacity begins to decline meaningfully. The practical replacement signal is runtime dropping below roughly 60 to 70 minutes on a full charge, at which point the robot may start returning to dock mid-clean on what was previously a single-charge floor plan. Cleaning the robot regularly and avoiding extended storage at very low or very high charge levels both help preserve cell capacity. Keep the charging contacts on the robot base and the dock landing pads clean: oxidation on either surface raises contact resistance, which forces the charging circuit to work harder and accelerates cell degradation over time. Wipe the contacts monthly with a dry cloth.

Maintenance at a glance

Component	Clean	Replace
Main brush roll (single DuoRoller models)	Every 1 to 2 weeks	Every 5 to 7 months
Main brush roll (DuoDivide models — clear divider channel each time)	Every 1 to 2 weeks	Every 5 to 7 months
Main brush roll (Qrevo Slim rubber rollers)	Wipe monthly	Every 6 to 8 months
HEPA filter (5,500 Pa to 7,000 Pa models)	Every 1 to 2 weeks	Every 2 to 3 months
HEPA filter (10,000 Pa to 11,000 Pa models)	Every 1 to 2 weeks	Every 2 months
HEPA filter (18,500 Pa models, both generations)	Every 1 to 2 weeks	Every 2 months
Mop pads (non-FlexiArm models)	Auto-washed by dock	Inspect at 8 weeks
Mop pads (FlexiArm models)	Auto-washed by dock	Inspect at 6 weeks
Side brush	Weekly; FlexiArm rail monthly	Every 3 to 6 months
Dock dustbag	—	Every 3 to 5 weeks
Dock dirty-water tank	Every 2 to 3 days	—
Dock spray nozzles (cold wash and 45°C models)	Monthly	—
Dock spray nozzles (75°C Dock 3.0 models)	Every 2 to 3 weeks in hard-water areas	—
Sensor windows and camera lenses	Weekly	—

Common problems and their maintenance causes

Mop pads leaving streaks along skirting boards or tile grout

The outer edge of the mop pad has lost its nap from 200 RPM spin wear. Because wear concentrates at the rim while the centre remains visually clean, pads can look serviceable but already produce streaks on narrow tile joints or painted skirting. The issue is most common on FlexiArm models such as the Qrevo Master, Qrevo Slim, Qrevo Curv, Qrevo Edge, Qrevo C Pro, Qrevo MaxV, Qrevo Pro, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, where extension travel concentrates wear at the rim. Replace the pads and run a dock self-clean cycle so new pads begin on a freshly rinsed base.

Hair wrap on the main brush despite the anti-tangle design

On DuoDivide models, including the Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, Qrevo Master, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, the central divider channel prevents single-roll wrap by intercepting hair before it reaches roller length. When the channel is loaded with compressed fibre, the interception fails and hair wraps onto both rollers simultaneously. Remove both rollers, clear the divider channel with a toothpick or the included cleaning tool, clean both sets of end caps, and confirm both rollers spin freely before reinstalling. Recurring wrap after a full clean indicates the service interval is shorter than the household shed rate requires, not a fault with the design.

Suction noticeably weaker than at first use

On 18,500 Pa models across both generations, including the Qrevo C, Qrevo C Pro, Qrevo Curv, Qrevo Edge, P20 Pro, Qrevo Curv 2 Pro, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, a clogged HEPA filter produces a distinct drop rather than a gradual fade, as the motor cannot fully compensate for the airflow restriction at this power level. Remove and inspect the filter first. If it is grey, replace it. If the filter looks clean, check the main brush roll and the suction inlet inside the dustbin for a blockage. On lower-suction models the decline is more gradual and usually noticed alongside a visibly loaded filter.

Persistent damp smell from mop pads after dock wash

On 45°C warm-air drying docks, including those paired with the Qrevo, P10, Qrevo S, Qrevo Plus, Qrevo Pro, Qrevo MaxV, Qrevo L, and Qrevo L Pro, incomplete drying is more likely than on the 75°C Dock 3.0 models. Wipe the dryer intake vents at the base of the dock to clear lint build-up, which restricts airflow even when the vent looks open. Check the dirty-water tank is not overdue for a rinse. If the smell persists despite clean vents and a rinsed tank, the pad has reached the end of its absorbent service life and replacement is needed; dock wash cycles cannot restore degraded fibre absorbency.

Mop pads returning with one side visibly dirtier than the other

On 75°C Dock 3.0 docks paired with Qrevo Master, Qrevo Slim, Qrevo Curv, Qrevo Edge, Qrevo C, Qrevo C Pro, P20 Pro, Qrevo Curv 2 Pro, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, limescale deposits from the 75°C wash water precipitate onto the spray nozzle faster than on cold-wash models. A partially blocked nozzle delivers uneven water across the two pads so one side leaves the dock under-rinsed. Wipe the nozzle area and descale with a dilute citric acid solution if build-up is visible, then run the dock self-cleaning cycle from the Roborock app to confirm even coverage is restored.

Auto-empty not completing or dustbin remains full after docking

The dock bag is full, or the suction channel between dock and robot dustbin port is blocked by caked dust. Replace the bag first. If the problem continues, wipe the docking port at the base of the robot and the port seal clean. Fine dust accumulates around the port seal from repeated docking cycles and breaks the airflow path needed for effective auto-emptying. This is especially common in pet households where the bag tends to fill faster and overdue changes are more likely.

Side brush no longer sweeping along walls on FlexiArm models

On Qrevo Curv, Qrevo Edge, Qrevo C Pro, Qrevo Master, Qrevo Slim, Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus, the side brush extends outward on an arc-shaped arm for wall-edge coverage. Grit or compressed hair on the arm rail restricts full travel so the brush no longer reaches its full extension. The symptom is a clean room centre alongside a persistent dust strip along skirting boards. Wipe the arm rail with a dry cloth and confirm by hand that the arm swings freely through its complete arc before the next clean session.

What consistent maintenance protects over time

On the Qrevo platform every consumable operates in relation to the others. The HEPA filter governs airflow across the brush chamber, which determines how quickly the dustbin fills; the dustbin fill rate determines how often the auto-empty cycle runs and how quickly the dock bag loads; a full dock bag causes the next auto-empty to stall, leaving the robot’s onboard dustbin unable to accept new debris, so the next run’s dust accumulates back on the floor or compacts into the brush. A single overdue consumable cascades through two or three others within a few weeks. Staying on the schedule across all components, including the less visible ones like the dock spray nozzle and the FlexiArm rail, keeps every model running at the suction tier it was sold at and protects the brushless motor from the extra current draw that accompanies any airflow restriction. Deferred maintenance tends to surface as a shortened robot lifespan rather than a single clear fault event.

The Plus.Parts® Maintenance Set covers the full service scope for Roborock Qrevo robots across all tiers: main brush roll, HEPA filter, mop pads, side brush, and dock dustbag in a single order matched to the consumable architecture of each specific model. It is a direct functional replacement for the original Roborock consumables, with the same fit and performance specifications, and having a complete set on hand means no individual component gets extended past its replacement interval while waiting for a separate delivery. When upgrading from a first-generation to a second-generation 18,500 Pa model, confirm the maintenance set matches the new robot rather than ordering from the existing set in stock.

How the Roborock Qrevo series models differ

The Qrevo family shares a common core: dual spinning round mop pads, a multifunctional auto-empty and auto-wash dock, and lidar-based navigation across most variants. Within that shared architecture, models diverge in suction tier, dock wash temperature, brush type, side brush mechanism, maintenance set generation, and, on the AdaptiLift-equipped chassis variants, in body height and threshold-crossing capability. The maintenance routine adapts to each of these differences rather than running identically across the range.

Original Qrevo and P10

The Qrevo is the entry point for the platform at 5,500 Pa. It pairs with the first-generation Multifunctional Dock using cold-water mop wash and 45°C warm-air drying, so limescale on the spray nozzle develops slowly and a monthly wipe is sufficient. Filter intervals sit at the longer end of the range at two to three months under daily use, and the dock bag holds up to several weeks of debris under light residential conditions. The P10 is the P-series branded version of the same platform sold in certain markets, sharing the same maintenance set entirely. This tier is also sold as QR52-00 and QX0PEA.

Qrevo S, Qrevo Plus, Qrevo Pro, and Qrevo MaxV

The Qrevo S, Qrevo Plus, Qrevo Pro, and Qrevo MaxV all deliver 7,000 Pa and share the same maintenance set. The Qrevo S uses the first-generation dock with cold-water wash; the Qrevo Plus, Qrevo Pro, and Qrevo MaxV upgrade to Dock 2.0 with hot-water mop washing. The Qrevo Pro and Qrevo MaxV add the FlexiArm extending mop for corner coverage, which shortens the mop pad inspection window to six weeks. The Qrevo MaxV further adds forward AI obstacle recognition; a smudged camera lens is worth a weekly wipe to avoid unnecessary detours. The P10 Pro is the P-series market variant for this tier. Other SKU variants in this set include QRS02-00, QRS52-00, QRS51-01, QR1PES, QR0PEP, QX1PEC, and R100053.

Qrevo L and Qrevo L Pro

The Qrevo L and Qrevo L Pro step up to 10,000 Pa with a 10 mm mop lift and a single-roller DuoRoller brush. Filter intervals run at roughly two months under daily use, closer to the shorter end of the two-to-three-month window. The dock on these models uses a three-stage mop wash without the 75°C hot-water circuit of the Dock 3.0, so spray nozzle maintenance stays monthly rather than biweekly. Regional SKU variants in this maintenance set include QV 35A, QV 35S, QR 598, QR 798, QVRS02-00, QVRRS02-00, QVRRS52-00, and RR-QRL52-03-BLK.

Qrevo Master and Qrevo Slim

The Qrevo Master operates at 10,000 Pa with the DuoDivide dual-roller anti-tangle brush, FlexiArm extending mop, FlexiArm side brush, and Multifunctional Dock 3.0 with 75°C hot-water washing. Compared with the Qrevo L, the key maintenance differences are the DuoDivide divider-channel clearing requirement at every brush service, and the biweekly spray nozzle wipe in hard-water areas instead of monthly. The P10S Pro is the P-series variant of this platform. The Qrevo Slim shares the Dock 3.0 and FlexiArm mop, but the chassis drops to 8.2 cm for low-clearance furniture and the main brush changes to a pair of counter-rotating all-rubber rollers. Rubber rollers resist hair wrap through a smooth-surface mechanism rather than a central divider, so service is a wipe rather than a cut, and the groove pattern in each roller needs a monthly inspection for compacted dust. SKU variants in this maintenance set also include QRM52-00, V20, QC0CRL, and QR2PPS.

Qrevo C and Qrevo C Pro

The Qrevo C and Qrevo C Pro bring 18,500 Pa suction to the DuoDivide dual-roller brush and pair with the Dock 3.0. The Qrevo C uses a conventional side brush; the Qrevo C Pro adds the FlexiArm side brush, pulling its arm rail into the monthly maintenance routine. Filter replacement on both sits at every two months, as the 18,500 Pa airflow loads the filter medium noticeably faster than the 10,000 Pa tier.

Qrevo Curv and Qrevo Edge

The Qrevo Curv and Qrevo Edge are the first-generation flagship Qrevo models, both running at 18,500 Pa with the DuoDivide dual-roller, FlexiArm side brush, FlexiArm extending mop, and Dock 3.0. The Qrevo Curv adds the AdaptiLift chassis and liftable omnidirectional wheel, which raises the body to cross thresholds up to 4 cm and lifts the mop pads to 17 mm when returning to dock. The AdaptiLift pivot rails are a monthly maintenance item specific to this model; grit accumulation prevents full lift travel and eventually leads to the robot failing to clear doorways it previously managed without issue. The Qrevo Edge shares the rest of the architecture without the AdaptiLift chassis. The P20 Pro is the P-series market variant for this tier. Further variants in this first-generation maintenance set include Qrevo Curv 5A1, Qrevo Curv 5XC, Qrevo CurvC, Qrevo Curv S5X, Qrevo Edge 5V1, Qrevo EdgeC, Qrevo Edge S5A, V10VIV, Qrevo S5V, Qrevo 5AE, QRC01-01, QRC02-00, QRES02-00, QRES52-00, QRRC52-02, QRSP52-00, RRE0VCM, RRE0PEE, and RRW0PEP.

Qrevo Curv 2 Pro, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus

The Qrevo Curv 2 Pro, Qrevo Curv 2 ProX, Qrevo CurvX, Qrevo EdgeT, QX Revo Ultra, and P20 Ultra Plus represent the second generation of 18,500 Pa Qrevo flagship hardware. Architecturally they share the DuoDivide dual-roller brush, FlexiArm extending mop, FlexiArm side brush, and Dock 3.0 with 75°C mop washing of the first generation, so the maintenance schedule runs on the same cadences: two-month filter cycles, six-week mop pad inspections, monthly FlexiArm rail wipes, and biweekly spray nozzle checks in hard-water areas. The key practical difference from the first generation is the consumable set itself: the brush roll, mop pads, side brush, and filter are all revised and are not interchangeable with the earlier Qrevo Curv and Qrevo Edge parts. When sourcing replacements, confirm the model name rather than assuming the same set applies because the product names are visually similar. The P20 Ultra Plus is the P-series branded variant of this generation, sharing the same maintenance set as the named Qrevo models in this tier. Regional SKU variants in this generation include RRE0VIS, RRE0VSC, and RRE0VSP.

Type reference

Type	Alternative type	Retail type
8.02.0269	8020269	—
8.02.0297	8020297	—
8.02.0411	8020411	HCTZ48RR
8.02.0388	8020388	—
QV35A	QV35S	—
—	—	QREVO MASTER SLIM MAINTENANCE SET